Model | AP-V41AWP | |||
Display power | 4 1/2-digit, 2-color, 7-segment LED (Character height: 4.5 mm 0.18″) AI indicator (green) Display cycle: 10 times/s | |||
Set and display range | -15 to +110% of F.S. *1 | |||
Operation indicator | Red LED x 2 (corresponding to control output 1 and 2) | |||
Resolution | Standard mode | AP-41M | 0.1kPa, 1mmHg, 0.1 inchHg, 0.01psi, 0.001bar | |
AP-41 | ||||
AP-43 | 0.01 kgf/cm2 | |||
AP-44 | 0.1kPa, 1mmHg, 0.1 inchHg, 0.02psi, 0.001bar | |||
AP-48 | 0.1 kPa, 0.001 kgf/cm2, 0.02 psi, 0.001 bar | |||
Focus mode | AP-41M | 0.01 inchHg | ||
AP-41 | ||||
AP-43 | 0.02 PSI | |||
AP-44 | 0.02 kPa, 0.2 mmHg, 0.01 inchHg, 0.004 psi, 0.2 mbar | |||
AP-48 | 0.02kPa, 0.2gf/cm2, 0.004psi, 0.2mbar | |||
Repeatability | ±0.2% of F.S. or less | |||
Hysteresis | Variable (Standard: 0.5% of FS; high-resolution/focus mode: 0.1% of F.S.) | |||
Response time | 1 (in high-speed mode only), 2.5, 5, 100, or 500 ms (selectable) *2 | |||
(chattering prevention function) | ||||
I/O | Control output | PNP open collector 100 mA max. (at 30 V or below) *3 with max. residual voltage of 1 V, 2 outputs (NO or NC selectable) | ||
Analog output (selectable) | 1 to 5 V with load impedance of 1 kΩ max. (or zero-shift input selectable) | |||
Zero-shift input (selectable) | ― | |||
Display temperature characteristic | ±1% of F.S. max. | |||
Unit expansion | ― | |||
Rating | Power voltage | 12 to 24 VDC ±10% with ripple (p-p) of 10% max. | ||
Power consumption | At 12 V | Normal | See below. | |
Eco mode | 600mW (50mA) or less | |||
At 24 V | Normal | 1200mW (50mA) or less | ||
Eco mode | 960mW (40mA) or less | |||
Environmental resistance | Operating temperature range | 0 to 50°C 32 to 122°F, no freezing | ||
Operating ambient humidity | 35 to 85%RH (no condensation) | |||
Vibration | 10 to 55 Hz, 1.5 mm 0.06″ double amplitude in X, Y, and Z directions, 2 hours respectively | |||
Material | Polycarbonate | |||
Accessories | End Unit,Head Connector, and Expansion Seal | |||
Weight | Approx. 80 g (with 2-m 6.6′ cable) | |||
*1 The focus range applies while in focus mode only. | ||||
*2 A response time of 100 or 500 ms applies if the AP-47 is used. | ||||
*3 The maximum current is 20 mA if the AP-V42W (P) is installed as an expansion unit. |
Electrnic components, Electronic Industrial Parts, Sensor, Switch
Keyence Proximity Switch Sensor AP-V41AWP
1. Condition: original new
2. Repeatability: ±0.2% of F.S. or less
3. Power voltage: 12 to 24 VDC ±10% with ripple (p-p) of 10% max.
$98.00
Based on 0 reviews
Be the first to review “Keyence Proximity Switch Sensor AP-V41AWP”
You must be logged in to post a review.
There are no reviews yet.